Dalsa BOA Manuel d'utilisateur Page 55
- Page / 136
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
resize
iNspect Express User’s Manual405-00026-00
47Rev 1600; 12 July 2010
c. Move the mouse over the image in the Work Area.
Click, release, move the mouse and click again, to
draw a Region shape where you want to read a bar-
code. Refer to the tip window. The Region is labeled
(Barcode1). When the Barcode tool is selected, you
can move and resize the Region.
If the code is part of the stamp or mold that forms your part, the code should move very little, and
your Region can be very close to the size of the code. If the code is part of a separate label or
etching process, you need a larger Region shape to allow for variation in the location of the code.
d. When you hover the cursor over the edge of the tool, the Region outline turns red, and a
message appears telling you to “Right-click to edit.”
e. Right-click on the highlighted Region outline. A Barcode Properties box opens. In this box
you can: rename the measurement, set the code type (System), and other parameters.
Code The code value read, or compare code to a fixed value.
Grade the quality of the barcode.
• Enable – check this box to report a measurement and pass or fail the part on this measurement;
or clear this box to not report a measurement and not pass or fail the part on this measurement.
• Value – If the barcode should always be the same value, type the expected barcode beside “Ex-
pression”. The code will fail if it does not match this value. If the barcode changes, leave an
asterisk (* for wild card) in this field, to report any read. You can use a question mark (?) for a
single character “wild card” or an asterisk (*) for a multiple character “wild card”. For exam-
ple; 123?? for any 5 character code starting with 123, or 123* for any code of any length start-
ing with 123.
The Padlock button
allows you to lock the Value, so it does not change as you change
parameter settings or move the ROI.
- Software User’s Manual 1
- 405-00026-00 1
- About This Manual 3
- Table of Contents 3
- List of Figures 6
- List of Tables 8
- The iNspect Application 9
- Introducing the iNspect GUI 10
- 2.Start Creating a Solution 11
- 3.Set up the Sensor 12
- Using the White Balance 13
- Using the Internal Timer 13
- Using the External Trigger 13
- Using the Exposure Control 13
- 6 Rev 1600; 12 July 2010 14
- Using the Calibration Tool 15
- 4.Set up Measurements 16
- 9Rev 1600; 12 July 2010 17
- Train the Color Map 18
- 11Rev 1600; 12 July 2010 19
- Apply Vision Tools 20
- Using the Drawing Tools 20
- Best Practice Suggestion 21
- Using Edge Sensitivity 21
- Using the Tolerance Settings 22
- Relative Numbers 23
- Using Preprocessing 23
- Using the Distance Tool 25
- 19Rev 1600; 12 July 2010 27
- Scale Properties 27
- Using the Angle Tool 28
- 21Rev 1600; 12 July 2010 29
- Angle Properties 29
- Using the Circle Tool 30
- 24 Rev 1600; 12 July 2010 32
- Using the Arc Tool 33
- 27Rev 1600; 12 July 2010 35
- Using the Edge Count Tool 37
- Using the Point Tool 39
- Using the Tip Tool 41
- 34 Rev 1600; 12 July 2010 42
- Tip Properties 42
- Using the Rake Tool 43
- 37Rev 1600; 12 July 2010 45
- Using the Pencil Tool 46
- 39Rev 1600; 12 July 2010 47
- Pencil Properties 47
- Using the Intensity Tool 48
- Using the Count Tool 49
- 43Rev 1600; 12 July 2010 51
- Using the Match Tool 52
- Using the Barcode Tool 54
- 47Rev 1600; 12 July 2010 55
- 48 Rev 1600; 12 July 2010 56
- Barcode Properties 56
- 50 Rev 1600; 12 July 2010 58
- Barcode Details Properties 58
- Using the 2-D Barcode Tool 59
- 52 Rev 1600; 12 July 2010 60
- 2D Barcode Properties 60
- 54 Rev 1600; 12 July 2010 62
- 2D Barcode Timing Properties 62
- 55Rev 1600; 12 July 2010 63
- 56 Rev 1600; 12 July 2010 64
- Using the OCR Tool 66
- 60 Rev 1600; 12 July 2010 68
- Using the Font Editor 69
- 63Rev 1600; 12 July 2010 71
- Font Spacing 71
- Using the Caliper Tool 73
- 66 Rev 1600; 12 July 2010 74
- Caliper Tool Adjusted 74
- Caliper Properties 74
- 67Rev 1600; 12 July 2010 75
- – Side A / Side B – 75
- Using the Contour Tool 76
- 69Rev 1600; 12 July 2010 77
- Contour Properties 77
- Using the Bead Tool 78
- 71Rev 1600; 12 July 2010 79
- Using the ColorMeter Tool 81
- Using the Spring Tool 83
- 76 Rev 1600; 12 July 2010 84
- 78 Rev 1600; 12 July 2010 86
- Using the Locator 87
- Using the Origin 89
- Add I/O Connections 91
- PLC Connections 91
- Setup I/O Connections 91
- 84 Rev 1600; 12 July 2010 92
- BOA Inputs 92
- BOA Inputs Configuration 92
- 85Rev 1600; 12 July 2010 93
- BOA Outputs 93
- BOA Outputs Configuration 93
- Scripting 94
- 88 Rev 1600; 12 July 2010 96
- 89Rev 1600; 12 July 2010 97
- Defined Variables 97
- 90 Rev 1600; 12 July 2010 98
- Create New Function 98
- Add New Function 98
- 91Rev 1600; 12 July 2010 99
- Free Edit 99
- Free Edit Window 99
- Setup History 100
- 93Rev 1600; 12 July 2010 101
- Edit Tolerances 103
- Graphing Measurements 104
- Setup Display 105
- History Recall 105
- 7.Save your Solution 106
- Monitoring from the Network 107
- Performance Tips 108
- Viewing Data Output 111
- HyperTerminal 112
- Network Commands 113
- Solution Summary Report 114
- Configuration Changes 115
- LOCATOR EXAMPLES 116
- 109Rev 1600; 12 July 2010 117
- Rotation Anchor 117
- Position Anchor 117
- Pencil Line Intersection 118
- 111Rev 1600; 12 July 2010 119
- Extending the Pencil Line 119
- Increasing the Search Area 119
- 112 Rev 1600; 12 July 2010 120
- Edge Count Tool – Circle 121
- Edge Count Tool – Rectangle 122
- Cascading Locators 123
- EQUATION EXAMPLES 125
- Override Examples 125
- Output Examples 126
- Delayed Event Function 127
- Related Functions 128
- Input Examples 129
- 122 Rev 1600; 12 July 2010 130
- 123Rev 1600; 12 July 2010 131
- 124 Rev 1600; 12 July 2010 132
- GLOSSARY 133
- 127Rev 1600; 12 July 2010 135
- 128 Rev 1600; 12 July 2010 136
Produits connexes et manuels pour Caméras de sécurité Dalsa BOA
(67 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.980 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels